Latest in All

I'm sharing the Blue Thunder project for a 500 engine with a brushless tail rotor.
The modeling process took me approximately two months. A friend did the 3D printing and assembly.

I've been thinking about a working miniature paint stencil. A 3D printer is the key to this. However, it needs to be printed very thinly, about 0.2mm. I then applied a spray adhesive to the back so that the paint doesn't bleed through it later.

A Roban head with some more details "Make it look real"

Designed for the Roban 700 AH64 Apache.

High detail Cobra cockpit made of 75 individual parts. I've designed 2 variations that fit Len Mount and Vario Cobras.

Wessex is almost done!

I have just completed a dummy turbine for the Lama in 1:6 scale. This can of course be supplied in any scale.
www.scale-print.de

Today I finished my trade fair model. An interior for a Vario Bell 429 on a scale of 1:5. You can probably see that I've been working with luxury interiors for the last 30 years in my previous job 🙂
The individual components can of course also be purchased separately.
www.scale-print.de

New in the program from today is the interior and equipment for the rear section of a rescue helicopter (in this case an H145 from Vario scale 1:5 in real scale 1:6). As always, all cushions are printed from rubber (TPU) by SCALE PRINT.
www.scale-print.de

Today I finally finished the work. Business Interior for the Vario Bell 429 in 1:5 scale.
www.scale-print.de

After I took a scan from the Vario Bell 429 on Saturday at Heli-Factory I have started to design the cockpit. The customer would like to have the business version including 5 seats in the back. To get it 100% scale the frames which are running in length direction needs to be positioned a little bit closer.
www.scale-print.de

I have just completed the first cockpit for the 1:4 Jet Ranger. This is exactly tailored to the Vario model. For sure it will be availble in any other scale.
www.scale-print.de

The air filter on top of the dome is now also available for the Hughes 500
www.scale-print.de

3D printers: Asking the group for their current recommendations on 3D printers. I’m inching forward on getting one. I use Fusion360 on my mill. Can I assume Fusion360 will push out programming for most of them?

I added the 3,200 item to my store yesterday. Take a look at it. There is certainly something suitable for your model. If not just contact me.
www.scale-print.de

This is the result of the last 2,5 weeks.
Cockpits for: Alouette III 1/6,7, Alouette III 1/6, Lama 1/5, Bell UH-1D 1/6, EC 120 1/4, EC 130 1/4,5, A109 1/4,8. All cockpits are of course illuminated.
www.scale-print.de

www.scale-print.de
New in the program from today is the cockpit of the Alouette III. Of course available in any scale.
www.scale-print.de

New in the program. The sand filter for the Vario NH90 in scale 1:8,9.
www.scale-print.de

For the Alouette III I have now constructed a winch. This can be made functional with a winch that must be mounted in the fuselage.
In addition, there are now many more parts for the Alouette III that I have designed which I will soon put online in my store.
www.scale.print.de

For the Starwood Lama (electric version) there is now also a dummy turbine on a scale of 1:5. At the request of a customer I have constructed a cover in the front area which completely covers the engine with the mounts.
www.scale-print.de

Installing new Fake-Tank and Tail Servo support.
Now the mechanic is well hidden